BRADFORD SCHOLARS

    • Sign in
    View Item 
    •   Bradford Scholars
    • University of Bradford eTheses
    • Theses
    • View Item
    •   Bradford Scholars
    • University of Bradford eTheses
    • Theses
    • View Item
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Browse

    All of Bradford ScholarsCommunitiesAuthorsTitlesSubjectsPublication DateThis CollectionAuthorsTitlesSubjectsPublication Date

    My Account

    Sign in

    HELP

    Bradford Scholars FAQsCopyright Fact SheetPolicies Fact SheetDeposit Terms and ConditionsDigital Preservation Policy

    Statistics

    Most Popular ItemsStatistics by CountryMost Popular Authors

    Bond of glass fibre reinforced polymer bars in high strength concrete

    • CSV
    • RefMan
    • EndNote
    • BibTex
    • RefWorks
    Thumbnail
    View/Open
    saleh, n.m.pdf (6.268Mb)
    Download
    Author
    Saleh, Najia M.
    Supervisor
    Ashour, Ashraf F.
    Lam, Dennis
    Sheehan, Therese
    Keyword
    GFRP bars
    Concrete
    Pull-out test
    Hinged beam test
    Bond
    Rights
    Creative Commons License
    The University of Bradford theses are licenced under a Creative Commons Licence.
    Institution
    University of Bradford
    Department
    Faculty of Engineering and Informatics
    Awarded
    2018
    
    Metadata
    Show full item record
    Abstract
    Very limited research studies have been conducted to examine bond of glass fibre reinforced polymer (GFRP) bars with high concrete strength. The current research project aims to compare between bond measured from a pull-out test and a hinged beam test for GFRP bars embedded in high strength concrete. Different parameters influencing bond such as GFRP bar diameter, embedment length and surface configuration were investigated in both test methods, while the bar position, i.e. top or bottom, was only studied in hinged beams. Seventy-two pull-out cubes, eight pull-out prisms and twenty-four hinged beams reinforced with GFRP bars were constructed and tested to failure. Twelve pull-out cubes and four hinged beams reinforced with steel bars were also tested for comparison purposes. The results showed that bond stress – slip curves obtained from various testing methods were similar, consisting of high initial stiffness, followed by nonlinear ascending and softening branches. In addition, it was found that the experimental bond strength obtained from hinged beams was higher than both bond strengths measured by the pull-out cube and pull-out prism. However, when a finite element analysis was conducted for hinged beams, it was shown that the tensile force in the reinforcing bar estimated by equilibrium conditions is overestimated as the large deformation of hinged beams at failure was not considered. Therefore, if the tensile force obtained from the finite element analysis is used to calculate the bond strength, it would be similar to that obtained from pull-out cube and prism. Moreover, it was found that the distribution of tensile and bond stresses was nonlinear along the GFRP embedment length and bond stress at the vicinity of the free end increased with increasing the load due to redistribution of bond stresses along the embedment length. Bond strengths were compared against the prediction methods provided in ACI-440.1R, CSA-S806, CSA-S6 and JSCE 1997. In general, all design codes showed conservative results for all specimens tested and ACI predictions gave a good agreement with experimental data compared to other codes. Artificial neural network models were developed to predict bond strength of GFRP bars in concrete. These models used bar diameter, embedment length, concrete compressive strength and concrete cover as input variables. The developed ANN models showed to be able to predict bond strength of GFRP bars in concrete and, therefore, were used to conduct a parametric study.
    URI
    http://hdl.handle.net/10454/17361
    Type
    Thesis
    Qualification name
    PhD
    Collections
    Theses

    entitlement

     
    DSpace software (copyright © 2002 - 2023)  DuraSpace
    Quick Guide | Contact Us
    Open Repository is a service operated by 
    Atmire NV
     

    Export search results

    The export option will allow you to export the current search results of the entered query to a file. Different formats are available for download. To export the items, click on the button corresponding with the preferred download format.

    By default, clicking on the export buttons will result in a download of the allowed maximum amount of items.

    To select a subset of the search results, click "Selective Export" button and make a selection of the items you want to export. The amount of items that can be exported at once is similarly restricted as the full export.

    After making a selection, click one of the export format buttons. The amount of items that will be exported is indicated in the bubble next to export format.